Connect With Us!

Retrospective: Cooper 250 Enduro: 1973-1975

Clement Salvadori
November 7, 2013
Filed under Other Motorycle Reviews, Retro + Vintage Motorcycle Reviews

Bookmark and Share
1973 Cooper 250 Enduro

1973 Cooper 250 Enduro

Back in those halcyon days of the early 1970s, two-stroke enduro models were the rage. If you wanted a play-bike, you bought Japanese.

If you were a serious rider, you bought European, as in Maico, CZ or Husqvarna. A California fellow by the name of Frank Cooper was the Maico distributor, and entertained himself on weekends by doing a bit of desert racing.

1973 Cooper 250 Enduro

1973 Cooper 250 Enduro

He appreciated the cost-effectiveness of the Japanese bikes, which tended to have rather twitchy frames, and the competitiveness of the Europeans, despite their many quirks which could easily put off a rider. Or throw him off, as the case may be. Frank decided he would develop an in-between machine, with a Euro-style chassis and reliable Japanese engine. And he could be his own boss, rather than listen to Maico’s directives.

This would require a factory—not something that Frank had in his backyard. But there was one down in Saltillo, Mexico, not far from the Texas border. It was Moto Islo, founded by one Isidro Lopez (Islo—first two letters of each name) back in 1955, where he began making little 50-to-200cc “tortilla” bikes for Mexican commuters and postmen, often using Italian and German engines in his own frames. The tortilla reference meant that these were everyday bikes, like tortillas were everyday food.

The story goes that Frank showed up in Saltillo with a Maico frame under one arm, a Yamaha DT 250 engine under the other, and asked Isidro if the factory could put the two designs together. Perhaps that is apocryphal—but it has the elements of truth. Because when the first Cooper 250 Enduro appeared at the Long Beach (California) Motorcycle Show in the late fall of 1972, there were distinct similarities.

1973 Cooper 250 Enduro

1973 Cooper 250 Enduro

The Cooper certainly stood out, with a bright lemon yellow fiberglass gas tank, fenders and triangular side-panels. Steel rims held the Bridgestone knobby tires in place, with a 3.00 x 21 on the front, a 4.00 x 18 on the back. Quick-stopping brakes were not considered necessary on enduros, as they were expected to spend most of their time on the dirt, so smallish single-leading-shoe full-hub drums did the work.

Front suspension used a Mexican-made Betor telescopic fork, giving a healthy 7.7 inches of travel. The rear swingarm had a pair of Boge shock absorbers, with adjustable preload, which could be ordered with specific spring requirements depending on intended use. Frank had aimed his sights high, and wanted to see these bikes used not only in enduros, but also for motocross, desert racing, TTs and even short track…with the factory setting everything up according to the wishes of the buyer.

The frame was a full cradle with double downtubes, made of lightweight 4130 chromoly tubing; nothing inexpensive about that. Though the engine had a rather Yamaha-ish look about it, Islo was using its own reinforced 200cc crankcase, albeit with a DT-style top end. Everything from the connecting rod on up could be sourced from a Yamaha parts book if needed. It had the same 70mm bore and 64mm stroke of the 246cc DT; imitation is the sincerest form of flattery.

1973 Cooper 250 Enduro

1973 Cooper 250 Enduro

The big difference was in the carburetion, with Yamaha using its Autolube system to mix the oil and the gas, and the Cooper relying on the old-fashioned premix way, adding oil to the gas in the 2.5-gallon tank and then running it through a 32mm Mikuni. A washable-foam air cleaner sat between the side panels.

The spark to the plug was provided by a flywheel magneto, and for anyone choosing to use Champions, an N-3G Gold Palladium was the expensive way to go. Exhaust gases exited via an upswept pipe which had a heat shield where the rider’s right leg might touch, then ducked behind the side panel and the shock absorber to end close to the taillight.

1973 Cooper 250 Enduro

1973 Cooper 250 Enduro

A duplex primary chain ran back to the close-ratio 5-speed gearbox, which looked very much like one on a CZ. In an entertaining bit of oversight, when the first bikes were given to the motorcycle press, the final gearing was such that the top speed could barely reach 50 mph; that was quickly changed.

Ground clearance was a reasonable 10 inches, with the seat at a tad over 31 inches. A reasonably comfy extended saddle kept the rider’s butt from protesting too much. A Nippon Seiko speedo went to an optimistic 100 mph. Dry weight was a claimed 227 pounds, with a wheelbase of 55 inches.

The first production bikes began appearing in U.S. shops in the spring of ’73, and riders were impressed with the power and the good handling. The engine, depending on tuning, was rated at anywhere between 23 and 28 horsepower. The factory had instructions for the serious contenders who wanted to increase performance, like reducing port timing on the piston-port engine by cutting four millimeters off the skirt of the piston. Or bolting on a 34mm carb.

1973 Cooper 250 Enduro

1973 Cooper 250 Enduro

However, buyers were less impressed with the way the fenders cracked and various fasteners came unfastened. Islo had not been very attentive to the manufacture of the fiberglass, which was too brittle, nor to the metallurgy used in many of the fittings, and the quality-control people seemed to always be out on a break. Worst of all was the cracking of the chromoly frame, as the tubing apparently had not been heat-treated correctly.

When reports of these deficiencies came in, Frank was on the phone to the factory, as well as making personal visits. He told them to redo the frame in mild steel and double the wall thickness—which added some 20 pounds to the weight, but it did not break. Isidro told his workers that these bikes were America-bound, and Americans were intolerant of imperfections. The factory was still making primarily those tortilla bikes, with the Coopers being assembled on a separate line, and the best wrenches were soon working on the enduros. And making them better.

Second problem was price. Frank had been hoping to undercut the Japanese models, but his Coopers were turning out to be more expensive than he had figured. The owner of this Cooper still has his original 1973 bill of sale: $1,038. While a Yamaha DT3 250 of that year cost $859, Honda’s two-stroke MT 250, $870. At the other end, a CZ 250 Enduro cost $1,280.

The bad reputation dogged the Cooper even after the problems had been pretty much fixed, and combined with the high price this doomed the bike. After producing some 1,200 motorcycles the Cooper line just died.

(This Retrospective article was published in the November 2013 issue of Rider magazine.)

Comments

One Response to “Retrospective: Cooper 250 Enduro: 1973-1975”

  1. Tony Campos on November 7th, 2013 10:56 pm

    I can see a cross breed of. Montesa, Ossa and Bultaco.
    But, bloody well done Mr Cooper. Riders need more of these European cross bred bikes. Don’t stop now.
    Tony

    [Reply]

Feel free to leave a comment...
and oh, if you want a pic to show with your comment, go get a gravatar!





Name:

Address:

City:

State:

ZIP: